#Garrard zero 100 auto problem how to
#Garrard zero 100 auto problem manual

The stylus brush should take some of the bounce out of the cantilever. A Stanton 681 EEE gets tried this week-end. But on a warped record, you could see the cantilever getting quite a workout because of the high mass tonearm. The articulating arm tracked perfectly - even on a warped record. I feel that the V-15 III added more bass punch, so I don't blame the Garrard on this. Bass smooth and defined but no real 'punch'. I expect a bright sound from Shure, but this exceeded my expectations. The highs were extremely open and detailed.

After balancing, tracking and anti skating was set to '1'.Р”В©. I figured that probably most of these were sold with a Shure M-91-ED, so it seemed like a good choice. Set up: Because of the reputation of a high mass tonearm, I wanted a durable yet good sounding cart, so I went with the Shure V-15 Type II.

#Garrard zero 100 auto problem how to

I haven't figured out how to adjust this yet.Р”РЃ. Seems to work OK, but when properly set, when cueing, the tonearm pulls to the outside of the record. Garrard got a patent on this system - no springs, all anti skating was accomplished with magnetics. My biggest complaint is with the anti-skating. The removable headshell fit well with no issues. Has a hokey stylus life indicator (added with the 'C'). It did balance fine, and the tracking force adjustment was accurate. Tonearm and related components: Seems loose to me - a lack of precision here. Garrards did have idler wheel drive systems figured out.Р”В§. Speed is dead on, even on a cold start, and stays there.

#Garrard zero 100 auto problem manual

Operation: Reminds me of a Dual 1019, with the separate manual on lever.Р”В¦. There are some plastic clips that are under spring pressure that need reinforcement to regain proper alignment.Р”Тђ. On the Garrard, the alignment studs for the plastic bezels are heat melted - removal can be dicey. We all know that 40 year old plastic will need some attention and repair. On Duals, plastic bezels are held in place with metal removable clips. But, once cleaned, they do work properly.Р”В¤. To start viewing messages, select the forum that you want to visit from the selection below. You may have to register before you can post: click the register link above to proceed. It looks to me like they wanted to add functions, and rather than re-engineer what they had to be more efficient, they just added parts.Р”Р€. Garrard Zero 100 Record Deck If this is your first visit, be sure to check out the FAQ by clicking the link above. Execution: The gearing and control levers are complex - more so than it needed to be. The tonearm and its plastic mounting case seemed cheesy.Р”Сћ. Please let me know, as I will be very grateful to restore it. It's been in my family since 1973, and I'm still in search of a flagship restoration for it. GARRARD-BROSCHRE 'HIFI-START IN FRANKFURT' - 301, 401, 4HF, THORENS TD 124. It arrived a few weeks ago, and was saved for a 5:30 AM Saturday project. Hard to find a good restoration shop to restore this Zero-100. GARRARD 401 Turntable 50Hz specification Audio Station NEAR MINT From Japan Used. Well I forgot about the Zero 100, until now. I also recall that it was faulted for it's high mass tonearm, vs the low mass that others were marketing at the time. As I recall, the design and engineering was lauded, but the unit itself was lacking in execution of fabrication. Around then, the Zero 100 was coming out to quite a bit of press. In 1971, as a teenager, I left my Garrard days when I bought my 1st Dual - a 1214. One of my Dual customers also sent me a Zero 100 (thanks Malcom in FL) for me to have fun with. What I mean by this is to dump the plastic parts of the original chassis and replace them with something sturdier.A bit of a departure for me. When I give it gas, needle responds correctly, also reads. One option would be to replace the plinth without changing the looks of it. Hello, anybody have a direction to point me to a area to look for a problem I am having with the Tach in my 96 3.4L Auto T100 When I start the truck, tach initially jumps up and reads correctly, then slowly settles back to zero idle. I understand that we have a different approach with this TT because I don't mind changing the looks a little, that is if the performance gets better. Furthermore, its a bit hard to find Zeros in Finland Whereas the price of a 301 is too high, I'd rather put that money to vinyl. Well I already have a Mission tonearm to try with my Zero so I will give it a go. I like your idea about using a hollow disc, but I quess it has one down side: the contact area with the ball bearing will somewhat increase. So I think I will start 'digging the scrapyard' for a suitable piece of ceramic material.

You are right about the size, although my platter seems to bee a bit different than yours or at least the small center piece with an opening on one side looks a little different.